18,OOO LBS. TRAILER WEIGHT
4,500 LBS. TRAILER TONGUE WEIGHT
ASSEMBLY INSTRUCTIONS
[ Fig. A ]
Height Above
Floor
Highest Posi-
tions
Medium Height
Positions
2” Farther
Back from Cab
Positions Clos-
est to Cab
Exchange Right and
Left RV Pivot Arms
4” Farther
Back From Cab
Distance from Cab
Front of Truck
Passenger’s Side Hole
Pattern as Viewed from
the Driver’s Side
16 3/4”
14 3/4”
15 3/4”
Lowest Posi-
tions
MounttheRVpivotarms(H)usingoneoftheninedifferentlocationsillustratedinFigureA.(These
ninelocationscanincreaseanddecreasetheclearanceforturningbetweenthetrailerandthebackofthe
truckcab.)TheatsideoftheRVpivotarmboltsatagainsttheplateintheRVbasewiththe20holesin
it.Usefour-½”x1½”bolts(A)insertingtheboltsintheRVBasewiththethreadstowardthecenterof
theRVBase,placetheRVpivotarmoverthefourbolts,usefour½”lockwashers(C),andfour½”nuts
(D)toattacheachRVpivotarmtotheRVbase.Torquetheboltsto80ft.lbs.
WARNING: B&Wrecommendsthatyouchecktheclearancebetweenthetruckcabandthetrailer.Com-
parethemeasurementtakenfromthecenteroftheRVCompanioncouplertothecab,tothemeasurement
takenfromthecenterofthekingpintothewidestpointofthetrailer.Thesemeasurementswillallowyou
toseehowmuchclearanceyouwillhavebetweenthecabandthetrailerwhiletowingandturning.
WARNING:B&Walsorecommendsthatyouchecktheclearancebetweenthebedsideandtheunderside
ofthefrontofthetrailerandtoallowadequateclearanceforthepitchandrollofthetrailerwhiletowing.
STEP ONE - INSTALL RV PIVOT ARMS
B&W Trailer Hitches
1216HWY224/POBox186
Humboldt,KS66748
620.473.3664
800.248.6564
F:620.473.3766
HELPFUL TIPS:
• APPROXIMATELY 15%-25% OF THE TRAILER WEIGHT SHOULD BE ON THE HITCH.
• THE HEIGHT OF THE KING PIN BOX AND PIVOT ARMS SHOULD BE ADJUSTED SO THAT
THE TRAILER IS APPROXIMATELY LEVEL FOR TOWING.
• ALLOW ADEQUATE CLEARANCE BETWEEN THE BED SIDE AND THE UNDERSIDE OF THE
FRONT OF THE TRAILER FOR PITCH AND ROLL OF THE TRAILER.
• LUBRICATE TOP SURFACE OF COUPLER WITH AUTOMOTIVE TYPE CHASSIS GREASE
OR USE A NYLON LUBE PLATE TO PROVIDE A LUBRICATED SURFACE.
• THE COMPANION RV HITCH WAS DESIGNED TO BE USED WITH THE TURNOVERBALL™
HITCH MOUNTING SYSTEM. OTHER USES WILL VOID THE WARRANTY AND ARE EX-
PRESSLY PROHIBITED BY THE MANUFACTURER.
• GREASE JAWS WITH AUTOMOTIVE TYPE CHASSIS GREASE.
• GREASE THE SADDLE THROUGH THE GREASE ZERK APPROXIMATELY EVERY SIX
MONTHS WITH MULT-PURPOSE GREASE. THIS ALLOWS THE COUPLER TO PIVOT
FREELY.
Call or Email us for Installation Support
800.248.6564
www.turnoverball.com
Model 3000
Hardware Kit
PART NUMBERS RVB3006 & RVC3006
Installation Instructions
Companion
TM
5th Wheel RV Hitch
8-1/2”x11/2”bolts(A)
1-1/2”x3”drawdownbolt(D)
8-1/2”hexnuts(C)
8-1/2”lockwashers(B)
1-1/2”atwashers(K)
4-5/8”locknuts(F)
4-5/8”atwashers(E)
2-3
1
/
2
”x4
1
/
2
”U-bolts(G)
2-RVPivotArms(H)
1-InstallationInstruction(I)
1-RVPost(J)
NOTE: We recommend reading instructions before beginning the installation.
COPYRIGHT 2013
B&WCustomTruckBeds,Inc.
ALLRIGHTSRESERVED
Model3000
06272013
Attention:Ifyouintendtousea
Companion5thWheelRVHitchina 2011 or
newer Fordor2013 or newer RAMTruck,
pleasecallusat800-248-6564forakitthat
llsvoidsinthetruckbedribpattern.Using
the Companion on a 2011 or newer Ford
or2013 or newer RAMwithoutthesupple-
mentalkitcouldresultindamagetothebed.
A-
B-
C-
D-
E-
F-
-G-
-H-
K
-
I
J-
STEP 6: PULL TEST
Havethetruckstationarywiththeemergencybrakeon,thetrailerwheelsblockedandlanding
gearstillrestingrmonthegroundsupportingtheweightofthetrailer.Makesurenooneisbetween
thetruckandtrailer,returntothecabofthetruck.Releasetheemergencybrakeandapplythetrailer
brakes.Trytopullthetrailerforwardwiththetruck.Ifthetrailerisproperlyhookedup,thewheel
blocksandtrailerbrakesshouldnotallowthetrucktomoveforward.Iftrailerisnothitchedcorrectly,
thetrailerwillseparatefromthetruck.However,withthelandinggearrestingrmlyontheground,
itwillsupportthetrailerandnotallowittodroporfallonthetrucksides.
STEP 7: UNATTACHING TRAILER
STEP 8: UNINSTALL HITCH
Lowerlandinggearandblockthetrailerwheels.Raisethetraileruntilthetongueweightis
removedfromthetruck.Then,unpintheCompanionRVhandleandrotatetotheopenpositionto
unlatchthejaws.Ifthejawsdonotopen,readjustingthelandinggearmayrelievepressureandallow
themtoopen.Usethesafetypintolockthehandleintheopenpositionandwhenyouaresurethat
thelandinggearwillsupportthetrailer,movethetruckforwardtoreleasethejawsfromthekingpin.
ThejawswillalwaysopenwhenthepressureofthetraileristakenofftheRVCompanionasthetruck
pullsaway.
TouninstalltheRVCompanion,removetheSaddlelockpins,grabtheRVsaddlehandlesand
lifttoremovetheRVcouplerfromtheRVpivotarms.ToremovetheRVbaseloosenthefour5/8”
nylonlocknutsonthetwou-boltsaroundtheRVpostandloosenthedrawdownbolt.Retractthe
Turnoverball™goosenecklatchpinhandleallthewayoutuntilitstopsandthenrotateitclockwise.
RemovetheRVbasefromtheGNhitchreceiversocket.
B&W Recommends that all bolted connections be checked for the correct
torque specication regularly. A visual inspection should be performed before
each time you tow.
Comments to this Manuals