Bw-trailer-hitches Turnoverball Model 1306 (Dodge) User Manual download pdf

Turnover Ball

Gooseneck Hitch Installation Instructions

Call or Email us for Installation Support

Model 1306R

B&W Custom Truck Beds, Inc.

To install the safety chain U-bolts it is necessary to drill four 1/2” holes through the truck bed oor. Drill the holes

from beneath the truck, through the four holes located in the 906R center section. Drop a U-bolt through each pair of

holes from the top side of the truck bed oor. Place a taperd spring and center lock nut on each of the four legs. Tighten

the center lock nuts until ush with the bottom of the U-Bolts.

STEP 7

1306R 04 05 2010

Hardware Kit

Parts List

[email protected]

www.turnoverball.com

B&W Trailer Hitches

1216 HWY 224 / PO Box 186

Humboldt, KS 66748

620.473.3664

800.248.6564

Fax:620.473.3766

STEP 5

Tighten all hardware in this order:

1) Tighten all 906R center section hardware to 80 ft. lbs.

2) Check to ensure that the hitch is square by measuring the space between the front cross member of the hitch

and the bed cross member so that the space is equal on each side of the truck.

3) Tighten the gold U-bolts to 60ft. lbs.

4) Tighten the 5/8” X 7 ½” hex cap screws to 60 ft. lbs.

5) Tighten the hardware that holds the side plates to the cross members to 80 ft. lbs.

Dodge 2003-2010

¾, & 1 Ton Long & Short Bed

Two & Four-Wheel Drive And

½, ¾, & 1 Ton Mega Cab Short Bed

11 - ½” X 1 ½” hex cap screw

9 - ½” hex nish nut

15 - ½” split lock washer

11 - ½” at washer

2 - 4” X 6 ½” gold U-bolt

2 - 5/8” X 7 ½” hex cap screw

2 - 5/8” hex nish nut

2 - 5/8” split lock washer

4 - 5/8” at washer

1 - 5/16” X 1” carriage bolt

1- 5/16” ange nut

Safety Chain Kit

2 - ½” U-bolt

4 - ½” lock nut

4 - spring

1 - 3/8” x ¾” hex cap screw



1- Front Cross Member

2- Rear Cross Member

3 - 906R center Section

4 - Left Side plate

5 - Right Side Plate

6 - 4” X 6 ½” Gold U-bolt

7 - 5/8” X 7 ½” Hex Cap Screw

8 - ½” X 1 ½” X 3 1/8” Silver U-bolt

9 - Tapered Spring

10 - ½” Center Lock Nut

11 - 5/8” Flat Washer

12 - 5/8” Split Lock Washer

13 - 5/8” Hex Finish Nut

14 - Latch Pin Handle

NOTE: We recommend reading instructions before beginning the installation.

STEP 6 – INSTALL LATCH PIN RELEASE HANDLE

 WARNING:LATCHPINWILLNOTFUNCTIONPROPERLYIFHANDLEISNOTINSTALLEDCORRECTLY.

Installthehandlefromunderneaththetruckbyinsertingitthroughtheslotintheendofthecentersectiontoward

thedriver’ssidereartireasshown.Attachthehandletothelatchpinasshownwiththehandleonthe“cabside”of

thesquaretabweldedtothepin.Theheadoftheboltmustbeonthehandleside,andthelocknutmustbeonthe

tabside.Thetabisweldedtothepininanoffset

positionsothatthehandlewillbelinedupover

thecenterofthepin.Ifthehandleisfastened

totheothersideofthetab,thehandlewillnot

functionproperly.Wheninstalledcorrectlythe

latchpinmaybedisengagedfromtheballby

pulling on the handle from the driver’s side

wheelwellandrotatingthehandleclockwise.

1 2

Summary of Contents

Page 1 - Model 1306R

Page 2 - BALL LOCATION:

The emergency brake cable bracket may need to be removed to install the side plate on the driver’s side. In this case the frame may have a similar s

Comments to this Manuals

No comments

Bw-trailer-hitches Turnoverball Model 1306 (Dodge) User Manual

Browse online or download User Manual for For the car Bw-trailer-hitches Turnoverball Model 1306 (Dodge). B&amp;W Trailer Hitches Turnoverball Model 1306 (Dodge) User Manual [de] [fr] [it]

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Bw-trailer-hitches Turnoverball Model 1306 (Dodge)

Browse online or download User Manual for For the car Bw-trailer-hitches Turnoverball Model 1306 (Dodge). B&W Trailer Hitches Turnoverball Model 1306 (Dodge) User Manual [de] [fr] [it]